香港管家婆马报玄机

Navigation
Application of technology
Recommended Products
MMD-R100C轮廓仪

MMD-R100C profilometer

MMD-120A型轮廓仪

MMD-120A profiler

contact us
Foshan Corporation
13889943666
Office 13420627674
Names of calipers and how to use them--Foshan Precision Measuring Instrument
Browse: Release Date: 2019-06-26

Name of each part of the caliper

M standard calipers

ABS Digital Caliper


Caliper scale reading

Vernier calipers

Dividing value 0.05mm

主标尺读数 16 mm Main scale reading 16 mm

游标尺读数0.15 mm Vernier scale reading 0.15 mm

————————————————

Reading 16.15 mm

0.15mm是读取的主尺刻度与游标刻度重合的位置。 Note: 0.15mm is the position where the main rule scale and vernier scale coincide.

Band calipers

Division value 0.01mm

主标尺读数 16 mm Main scale reading 16 mm

表盘读数 0.13 mm ②Dial reading 0.13 mm

————————————————

Reading 16.13 mm

Caliper measurement application

Universal calipers:

Outer dimension measurement

Internal dimension measurement

Step measurement

Depth measurement

Dedicated calipers:

Groove diameter measurement

Narrow groove diameter measurement

Step Cross Section Measurement_Offset Caliper

Wall thickness measurement_wall thickness caliper

Inner diameter measurement_Inner diameter caliper


Use of calipers

Examples of M-type standard calipers:

Precautions before use

1. Wipe the reference end surface and sliding parts with a small amount of micrometer lubricant.

2. Move the ruler frame over the entire stroke to check if it is stuck.

3. After cleaning the measurement surface, make it fit and confirm the following:

外侧测量面:对准光源时,看不到光是正常的。 Outside measuring surface: It is normal to see no light when aiming at the light source. (figure 1)

When stains, chips, or burrs cannot be completely attached, light may sometimes be seen. (figure 2)

内侧测量面:对准光源时,仅能看到一点光的状态是正常的。 Inside measuring surface: When aiming at the light source, it is normal to see only a little light. (figure 1)

请确认基准点。 Check the reference point. (image 3)

Cautions in use

1.   When reading the scale, point your eyes at the front and pay attention to parallax. (Figure 4)

2. When measuring, please use a certain force and try to measure at the base of the measuring claw. (Figure 5)

3. Do not measure with the measuring surface tilted. (Figure 6)

Precautions after use

1. After use, check for damage to all parts and clean the whole.

When using in places with water-soluble cutting oil, etc., be sure to perform anti-rust treatment after cleaning.

2. Open the outer measuring claws by about 0.2 to 2 mm. (Figure 7)

3. Do not store in high temperature, high humidity, dusty, oily places.

* If a digital caliper is used, please remove the battery if not used for a long time.

佛山市精测计量仪器设备有限公司 总部 Company Name : Foshan City Precision Measurement Instruments Co., Ltd. ( Headquarters )


广东省佛山市顺德区陈村镇顺联机械城 17座二层2008室 Address : Room 2008, 2nd Floor, Block 17, Shunlian Machinery City, Chencun Town, Shunde District, Foshan City, Guangdong Province
:0757-29289282 Phone : 0757-29289282
:0757-29289282 Fax : 0757-29289282  
:13889943666 Mobile : 13889943666
QQ: 975802545
:13889943666 WeChat : 13889943666
:wxetech.com Website : wxetech.com
E-mail: fsjcyq@163.com

Zhongshan Zhuhai Jiangmen Zhaoqing

:13420627674 Mobile : 13420627674
QQ: 2399009720
:13420627674 WeChat : 13420627674

   

为您推荐选型 公司公众号关注后为您提供专业的产品测量知识 Sales manager- recommend the company's public number for you-provide professional product measurement knowledge after attention

Company route:
Drive to Shunlian International Machinery City 17 Shunlian to make money
Arrive at 17 Shunlian Zhizhihui and take the elevator to the second floor (as shown below)

After reaching the second floor, go straight to the right (as shown below)

Go straight to the company location (as shown below):